Secrets Of Mosfet Cross Reference and Replacement Guide
A Semiconductor Replacement Guide Searching for the right mosfet cross reference or datasheet, one has to look for a semiconductor transistor replacement data book and not the Philip ECG master replacement guide. Almost all the transistor replacement book will published out the specification of a particular components such as type of component it belong whether it is a fet, scr, bipolar transistor, horizontal output transistor and also the voltage, ampere, wattage, ohm, frequency and suggested substitution part number.
From my experienced, the substitution part number that was recommended by the data book is not always 100 % match. If you have the time, I would like to suggest to you that, find the right part number by yourself rather than depending on the transistor data book.
It is the same when you look for horizontal output transistor (HOT) specification which doesn't mean that the bigger specification, the better the substitution part number is. In searching for Mosfet cross reference, you have to look at the ohms value which is provided by the transistor data book besides the specification of voltage, ampere and the wattage. The replacement, besides the same or higher in voltage, ampere and wattage, one should also consider the ohms value. The ohms value has to be as close as possible.
Arrow is showing the mosfet ohms value in a transistor substituion book
If the original fet part number is 1 ohm then a good replacement mosfet must have the ohm values between of 0.5 to 1.5 ohm. Do not substitute it with a too high or too low ohms value as this will make the mosfet run warmer and eventually blow the mosfet itself. Even though you can get a replacement with a higher voltage, ampere and wattage, if the ohms value is too low or too high, the mosfet will still burnt after on for quite a while.
It runs well for sometimes before it breakdown again. After two weeks the customer brought back the printer with the same complaint which is no power. Upon checking the power side I found the same mosfet gave up again. Substituting with another mosfet part number that have a similar specification especially the ohms value solved the printer no power symptom.
Specification with larger voltage, ampere and wattage don’t guarantee that the replacement mosfet will work. So, taking the mosfet ohms value into consideration, you will have a higher chances to repaired the equipment and sometimes the replacement mosfet will also last longer.
|
|
Ownhammer -
Or, more precisely, they make (IRs) — digital snapshots of how a specific guitar cabinet, with a specific speaker, placed in a specific room, captured by a specific microphone, actually breathes . The Problem Before OwnHammer For decades, the "amp-in-the-room" sound was the holy grail. Then came digital modeling (think Kemper, Fractal, Line 6 Helix, Neural DSP). Modelers were brilliant at replicating the preamp and power amp of a vintage Plexi or a Mesa Boogie. But they kept sounding… flat. Two-dimensional. Like a photo of a steak instead of the steak itself.
So the next time you hear a crushing modern metal riff or a buttery blues solo on a record and think, "Damn, that cabinet sounds perfect" — there’s a very good chance you’re listening to a silent, black box in a rack, playing a 500-millisecond file created by a guy in a basement who decided that air was worth capturing. ownhammer
If you’ve spent any time in the rabbit hole of modern guitar tone, you’ve likely heard the name OwnHammer whispered in forums, shouted in YouTube gear reviews, or listed in the credits of a platinum record. But unless you’re a hardcore home recordist or a touring guitarist who ditched their 4x12 cabinet five years ago, you might not know what it is. Or, more precisely, they make (IRs) — digital
Why? Because the are 70% of your electric guitar tone. Moving a mic on a real speaker by an inch changes everything. The digital models of that interaction were, frankly, bad. Modelers were brilliant at replicating the preamp and
So, let’s clear that up: OwnHammer doesn’t make guitars, pedals, or amps. They don’t make microphones.
Copyright@ 2006-2014-www.ElectronicRepairGuide.com All Rights Reserved